玻璃钢雕塑我们在各种广场、公园等公共场所都是可以看见的，这种雕塑可以根据需求制作出不同的款式，每种款式的颜色，特点都是不一样的么他们表达的含义也是不同的，玻璃钢雕塑主要是有玻璃钢制成，玻璃钢有属于复合材料的一种，其实制作工艺也是非常有难度的，下面小编就带大家了解下关于玻璃钢雕塑的制作方法及上色流程!
FRP sculptures can be seen in various public places such as squares and parks. This kind of sculpture can be made into different styles according to the needs. The colors and characteristics of each style are different. The meaning they express is also different. FRP sculptures are mainly made of FRP, which belongs to a kind of composite material. In fact, the production process is very good It's difficult. Let's learn about the production method and coloring process of FRP sculpture!
一、玻璃钢雕塑的制作方法
1、 The manufacturing method of FRP sculpture
1、模具制作
1. Mold making
1)泥塑/泡沫雕塑：雕刻家根据甲方提供的图纸进行雕刻，更终甲方确认雕塑是否需要修改直完成。
1) clay sculpture / foam sculpture: the sculptor engraving according to the drawings provided by Party A. finally, Party A confirms whether the sculpture needs to be modified until it is completed.
木模：要求产品尺寸准确，模具大师雕刻，形状，修改和验证它与木材。我们称之为模型，产品的外观。
Wood mold: requires accurate product size, mold master to carve, shape, modify and verify it with wood. We call it the model, the appearance of the product.
2)石膏模应复制在粘土模或泡沫模上，石膏模是一次性的，只能生产一两种产品。
2) plaster mold should be copied on clay mold or foam mold, plaster mold is disposable, and can only produce one or two kinds of products.
3)玻璃钢模具可直接复制在木模上，玻璃钢模具可保存，使用寿命约100件。
3) The FRP mold can be directly copied on the wood mold, and the FRP mold can be permanently stored, with a service life of about 100 pieces.
2、空白
2. Blank
先用刷子将胶衣涂在模具表面，半干后铺上纤维布;
First, apply the gel coat on the surface of the mold with a brush, and then lay the fiber cloth after it is half dry;
开始用刷子刷树脂使其渗透，然后铺布，逐层刷树脂，达到所需厚度。
Start to brush the resin with a brush to make it penetrate, then spread the cloth and brush the resin layer by layer to reach the required thickness.
3、修模：脱模是指将坯料从模具中取出。
3. Mold repair: demoulding refers to taking the blank out of the mold.
4、制作玻璃钢模具：石膏模制作的玻璃钢制品经打磨修补后，复制成批生产。
4. Making FRP mould: the FRP products made of gypsum mould are copied and produced in batches after being polished and repaired.
5、喷油处理：
5. Fuel injection treatment:
1、用180×砂纸打磨产品，去除产品表面脱模蜡，用原子灰填充产品表面的针孔和夹紧线。
1. Firstly, 180 × sandpaper is used to polish the product, remove the demoulding wax on the product surface, and fill the pinholes and clamping lines on the product surface with atomic ash.
2、用220×砂纸打磨，喷道底漆，选择不合格部位，加入原子灰。
2. Polish with 220 × sandpaper, spray the first primer, select unqualified parts, and add atomic ash.
3、用360×砂纸打磨，喷第二道底漆，再用细红灰修补。
3. Polish with 360 × sandpaper, spray the second primer, and then repair with fine red ash.
4、用800×砂纸打磨，开始喷涂汽车漆干燥。
4. Use 800 × sandpaper to polish and start spraying automobile paint for drying.
5、表层干燥后，生产主管应检查表层是否漏油，少喷;
5. After the surface layer is dry, the production supervisor shall check whether the surface layer leaks oil and spray less;
二、玻璃钢雕塑上色流程
2、 Coloring process of FRP sculpture
1、刚制作完结的玻璃钢雕塑表面有一层蜡，为了让该雕塑更加的便利上色，就需求把上面的蜡打 磨掉，因此首要是运用砂纸打磨玻璃钢雕塑表面。
1. There is a layer of wax on the surface of the finished FRP sculpture. In order to make the sculpture more convenient for coloring, it is necessary to polish the wax off the surface. Therefore, the first thing is to use sandpaper to polish the surface of the FRP sculpture.
2、刚制作完结的玻璃钢雕塑有一些不平或许坑洞，因此，要先用油画刮刀也可以凑合用，小 比较便利处置，大面积的就有些艰难了，不容易找平。
2. There are some unevenness or potholes in the glass fiber reinforced plastic sculpture just finished. Therefore, it is necessary to use the oil painting scraper first. The small center is more convenient to handle. The large area is a little difficult and not easy to level.
3、玻璃钢雕塑的后期处置一方面是修整脱模后产品的部分缺点，更重要的是制作表面作用，常选用的表面作用是仿紫铜色与仿青铜色，关键是制造色浆。
3. On the one hand, the post-processing of FRP sculpture is to repair some defects of the products after demoulding, and more importantly, to make the surface effect. The commonly used surface effect is to imitate the copper color and bronze color, and the key is to make the color paste.
