玻璃钢抽象雕塑是通过人们的灵感想法来创作的一种，这种雕塑不规则，不像动物雕塑那样固定的模式，这种雕塑让人们联想到的更多，也可以说是每一个人对某一种抽象事物的理解，因此这种雕塑可以给大家一些启示。山东景观雕塑公司补充的一点就是，这一种雕塑与环境的结合也让城市变得更加拥有色彩，更加的生动。
FRP abstract sculpture is a kind of creation through people's inspiration. This kind of sculpture is irregular, unlike the fixed pattern of animal sculpture. This kind of sculpture makes people associate more with it. It can also be said that everyone understands an abstract thing. Therefore, this kind of sculpture can give you some inspiration. Shandong Landscape Sculpture Company adds that this combination of sculpture and environment also makes the city more colorful and lively.
玻璃钢雕塑模具材料主要有三类：
There are three main types of FRP sculpture mould materials:
1、用玻璃钢资料做成的模具型腔，也叫硬模法。也就是在玻璃钢模具上翻制玻璃钢雕塑，玻璃钢模具普通采用手糊成型办法，制造前应设计成型线路。
1. The die cavity made of FRP material is also called hard die method. That is to say, the FRP sculpture is turned over on the FRP mould. The hand paste forming method is commonly used in the FRP mould, and the forming circuit should be designed before manufacture.
2、石膏资料做成的模具型腔，也叫碎模法。但石膏资料强度低、放置时间长时容易变形。
2. The mold cavity made of gypsum material is also called broken mold method. However, the gypsum material is of low strength and easy to deform for a long time.
3、硅橡胶资料做成的模具型腔，也叫软模法。硅橡胶资料运用前为流体状态，活动性及填充性好。配制后经交联反响构成橡胶弹性体，可具有较大的弹性变形。交联后的硅橡胶密封性好，与原模及玻璃钢皆不粘接。用其做玻璃钢雕塑模具的外表层资料，既能够高质量地复制出作品的外形，又能够保证顺利脱模。但是，硅橡胶交联体容易变形，在用作模具时，需有支撑载体。能够应用玻璃钢易成型的特性，用作模具的载体资料。详细的模具制造办法是：将配制好的硅橡胶分几次涂剧在原模上，硅橡胶层应在1mm后以上。待硅橡胶交联后，在硅橡胶上再成型厚度为3mm左右的玻璃钢层。玻璃钢固化后，沿着划分出的单元块将整体模具切开，切割时留意将玻璃钢层及硅橡胶层同时切开。
在单元块间制造衔接肋，衔接肋处应设定位槽，以保证经过衔接肋使单元块模具组合成一整体。以上工作完成后，将玻璃钢单元块脱模，然后脱下硅橡胶层，脱下的硅橡胶块立刻放回玻璃钢单元模中。
3. Mold cavity made of silicone rubber material is also called soft mould method. Silicone rubber data were in fluid state before application, with good mobility and filling. The rubber elastomer can be formed by cross-linking reaction after preparation, which can have large elastic deformation. The cross-linked silicone rubber has good sealing property and does not bond with the original mould and FRP. Using it as the surface material of FRP sculpture mould can not only reproduce the appearance of the work with high quality, but also ensure the smooth demoulding. However, the cross-linking of silicone rubber is easy to deform, so it needs support carrier when it is used as a die. It can be used as the carrier material of the mould by using the easy-forming property of FRP. Detailed die manufacturing method is: the prepared silicone rubber is painted on the original model several times, and the silicone rubber layer should be more than 1 mm later. After crosslinking of silicone rubber, the fiberglass reinforced plastic (FRP) layer with a thickness of about 3 mm was formed on the silicone rubber. After FRP solidification, cut the whole die along the dividing blocks. When cutting, pay attention to cutting both FRP layer and silicone rubber layer at the same time. The joint ribs are manufactured between the units, and a slot should be set at the joint ribs to ensure that the unit die is combined into a whole through the joint ribs. After the above work is completed, the FRP unit block is demoulded, then the silicone rubber layer is removed, and the removed silicone rubber block is immediately put back into the FRP unit die.
After reading the above, I wonder if you all understand it. Today's wonderful content is provided by the friendship of Shandong Landscape Sculpture Company. I hope it will be helpful to you. More wonderful content is welcome to consult our official website: http://www.mmyljg.com.
